Installation and Quick Configuration Manual
This section includes the following articles:
- Introduction
- Comparison chart: Master modules
- Comparison chart: LoRa gateways
- Comparison chart: PDUs
- Monitoring units, Gateways & PDUs
- VT225t Room monitoring unit
- VT335t Monitoring unit
- VT335G Monitoring unit
- VT336t Industrial Monitoring Unit
- VT604t Switched PDU with 4 outlets
- VT608t / Switched PDU with 8 outlets
- VT825t Remote Monitoring Unit (v5.0)
- VT855t Data Center Monitoring System
- VT-PDU 4MS Metered & Switched by Outlet PDU
- VT-PDU 4PS Switched & Managed PDU
- LR800 gateway & server
- LoRaWAN sensors
- Sensors and meters
- Extensions
- Accessories
- Installation (hardware)
- Connecting LoRaWAN Sensors
- Connecting NC-NO-COM relays
- Connecting 12V devices to 12V outputs
- Connecting an LTE 4G modem
- Connecting USB cameras (USB100)
- Connecting analog sensors
- VT407 AC current converter (link)
- VT410 DC voltage monitor
- VT420 Converter 4-20mA
- VT500 Temperature sensor
- VT501 Outdoor temperature sensor
- VT510 Humidity sensor
- VT520 AC voltage monitor
- VT530 Access sensor
- VT540 Vibration sensor v2
- VT550 Wind velocity meter
- VT560 Smoke detector
- VT572 Radar motion sensor v2
- VT591 Leak sensor & WLC / Leak detection cable
- VT593 Spot leak sensor
- VT594 BMS leak water sensor
- VT520DIN AC Voltage monitor (link)
- VT580 Dust particle sensor
- VT416 Bidirectional DC Ammeter
- Connection CAN devices & sensors
- Comparison chart: Extension units, CAN devices, Sensors
- VT408 Analog sensor extension unit
- VT440 / Dry contacts unit & VT32 / Dry contacts board extension
- VT450 Pressure, humidity and temperature sensor
- VT460 Smoke, humidity, temperature sensor (v8.1)
- VT490 Humidity and temperature sensor
- CAN-12V-1A / CAN Power Supply
- Connecting AC, DC meters
- Connecting Modbus devices
- Connecting readers
- Connecting dry contacts
- Connecting power backups
- Buttons and switches
- Using terminal connectors
- Web Interface (Initial Configuration)
- Web Interface (Further Configuration)
- Networking
- Setting up a modem
- Virtual elements & System tree panel
- Onboard sensors
- Sensor configuration
- Creating dew point element / sensor
- Monitor network elements/meters/devices
- Creating notifications
- AC, DC meters configuration
- Creating groups of elements
- CAN configuration panel: setting up CAN
- Logic schemes
- Creating floor map plan
- Creating trigger
- Backup, restore and reset.
- Dry contacts settings panel
- Relay switching (NC NO) / Outlets switching
- Creating a timer / schedule
- Graphs panel
- System Log & Event log panel
- 12V relay configuration
- Configuring Modbus devices
- Creating virtual Math element
- Configuring cameras & cameras panel
- Duplicator program
- Settings examples
- Inventory
- Monitoring units (inventory)
- Analog sensors (inventory)
- VT410 package content
- VT420 package contents
- VT500 package content
- VT501 package content
- VT510 package content
- VT520 package content
- VT520DIN package content (link page)
- VT530 package content
- VT540 package content
- VT550 package content
- VT560 package content
- VT572 v2 package content
- VT580 package content
- VT591 package content
- VT593 package content
- VT594 package content
- WLC package content
- CAN sensors and modules (inventory)
- Extension units (inventory)
- AC / DC meters, current converters (inventory)
- Accessories (inventory)
- Mounting kits (inventory)
- Readers (inventory)
- Inventory pictures (for admin use)
- Cameras (inventory)
- Upgrade and restore options
- Cleaning, battery & fuse disposal and replacement