VT604 / Switched PDU v2.1 (legacy)
- Vladimir Tayzhev
- Vasily T.
- Admin1
Product page: https://vutlan.com/power-distribution-units/84-vt604-switched-ip-pdu.html
Datasheet page: https://vutlan.atlassian.net/l/cp/u8uV4uxh
Function and purpose
The device is used for load management and allows to switch on/off or reboot up to 4 outlets.
It has a built-in temperature sensor, can connect 2 additional sensors, 2 dry contacts, two 12V devices (for example, alarm beacons), an internal LTE modem (Ordered separately!), and USB-сam.
There are built-in servers and agents like HTTP, HTTPS, SNMP v1, 2c, 3, SMTP, Radius, Syslog, FTP, DHCP.
Physical description
1. LEDs:
"ACT / STATUS" - green - indicates appliance status
"E1" - Green - indicates 12V E1 relay status
"E2" - Green - indicates 12V E2 relay status
"CAN" - Green - indicates CAN bus status; "CAN" blinks slowly - nothing is connected; "CAN" blinks fast - configuration is in the process; "CAN" glows constantly - connected to CAN devices
"ERROR" - red - indicates error and traffic.
the operational mode of the device: the norm is extinguished, not the norm - a constant glow;
software update mode: switches at a rate of 2 times per second;
"OUTLETS 1 - 8" - orange - indicates outlet status.
2. "LAN" - Ethernet 10/100 Base-T port, provides an Ethernet connection.
• LEDs - "yellow" (status) and "green" (traffic) show the network traffic. The status LED: flashes green when the system starts up, and shows the connection state (constant green light - the connection is established, blinking green - the connection attempt).
3. This is a slot for "VT760 / LTE modem". The modem is purchased separately!
3a. "ANTENNA" - connector connects the antenna to "VT760 / LTE modem" for correct time detection.
3b. "Status" - displays modem status. Blinking = working.
3c. "Main antenna" - Connector, used when the LTE modem is installed inside of the appliance to connect the LTE main antenna. (The main antenna is supplied together with the modem).
3d. "Auxiliary" - Connector, used when the modem is installed inside of the appliance to connect the LTE auxiliary antenna. The additional antenna helps to strengthen the signal level. (Auxiliary LTE antenna and antenna output are ordered separately from the modem).
3e. "SIM card" - SIM card slot with an injector.
4. "A1..A2" - x2 RJ12 analog sensor inputs with auto-sensing.
5. "USB" - type miniAB USB-port 2.0, required to connect a USB camera or to restore an appliance.
6. "RESTART" or "RESET" - restarts the appliance.
7. 4x power "OUTLETS" C13
8. POWER INPUT C14 240V 10A
9. "FUSE" - 10A. 5х20 мм.
10. "" - External chassis grounding, M4 thread.
11. "Dip switch" Normal ↑ Off - the system should be always switched to this mode.
Recovery ↓ On - use this option only in case you need to recover manufacturing settings.
12. "DRY CONTACTS 1...2" - x2 dry contacts terminal (type IN)
13. "OUTPUT 12V 0.25A" - x2 12V 0.25A output electronic relay terminals
14. "CAN" - digital connector RJ12 for the connection of CAN sensors and CAN extensions on a CAN bus, with auto-sensing.
Inventory
Connection overview diagram
Dimensions
Technical specifications
Installing a modem
Please refer to the following articles:
LTE modem is ordered separately and can be integrated inside the system. Modems are purchased separately.
Installing the device into a 19" rack
Use x3 pcs of supplied screws (M3 6mm) for each bracket to fix it on each side of the enclosure as shown in the picture below. The screws and brackets are supplied with the unit.
Initial configuration
Device configuration
Frequently asked questions
Question | Answer |
|---|---|
Does VT604 monitor the power consumption? | No, this is not supported. |
Developer notes: metal case VT604 v2.1
Copyright:
Vutlan s.r.o. (LLC)
Remote Infrastructure Monitoring and Control
43 ul.Svornosti, 821 06 Bratislava,
Slovak Republic