VT408DIN Analog sensor extension unit

Owned by Vladimir Tayzhev
Last updated: Oct 08, 2024
4 min read

Content

VT408DIN sensor extension unit (front)(rail)(adj20).png
VT408DIN_sensor_extension_unit_CAN (A4 rail)(adj40).png

Product page: VT408DIN / Sensor extension unit

Datasheet page: https://vutlan.atlassian.net/wiki/spaces/DEN/pages/edit-v2/1340440577

Function and purpose

Increases the number of analog sensors connected to any Vutlan monitoring unit. Each unit connected adds 8 analog sensors. Connects on CAN port and allows further CAN daisy chain connection. Sensors connected to the extension unit appear in the system automatically.

Up to x24 VT408 units can be connected on a CAN bus line. CAN-12V-1A / CAN Power Supply has to be used to provide additional power on a CAN bus line.

Physical description

Module VT408DIN is designed to expand the number of analog sensors connected to monitoring systems.

 


1. "A1..A8" - x8 RJ11 6P4C analog sensor input ports with auto-sensing.

2. "Power" - for connection of external power supply 12V DC, 05A.

3. LEDs:

   3a. "RUN" - indicates appliance connection status to the main module,

   3b. "ERROR" - indicates the appliance lost connection to the main module.

  • ERROR is lit continuously, RUN blinks - the unit has no connection with the monitoring unit.

  • ERROR is continuously lit, RUN repaid - extension unit communicates with monitoring unit, however, it is not included in the monitoring system (not configured).

  • ERROR repaid, RUN lights up continuously - the extension unit is included in the work as part of a monitoring system.

4. "Terminator" - This switch should be turned "ON" on the last sensor/device in the CAN chain.

5. "CAN bus" - x2 equivalent digital RJ11 6P4C connectors for the connection to the master module.

Function

VT408DIN module is developed to expand the number of analog sensors connected to the monitoring system. The picture below illustrates the expansion example:

Mounting

DIN rail mounting

  1. There are DIN rail mounting hooks at the top and the bottom of the case. Pull them outwards.

  2. Press the enclosure against the DIN rail so that it fits behind the enclosure.

  3. Tap the hooks back in to snap to the DIN rail.

DIN rail unmounting

  1. Use a screwdriver and pull the x3 hooks on the enclosure outward.

  2. Pull the enclosure away from the DIN rail.

DIN rail extension and wall brackets are purchased separately.

Installation

  1. Connect any CAN port of the unit by RJ11 6P4C cable supplied to the CAN port of the previous CAN unit or the monitoring system. The red LED lights up.

  2. If this CAN device is the last in the CAN bus chain, then switch the Termination ON. If not, keep it Off.

  3. If the unit is far 10m away from the monitoring unit or more, connect an additional auxiliary power supply. In all other cases, the use of an external power supply is desirable.

CAN setting

The extension module has a built-in element:

  • Power -  the element of relay
    This element, by designation, is identical to the Analog Power element of the monitoring module. It turns on or off the power of the analog sensors.
    The analog sensor power off for a few seconds is used to reset the alarm of the VT560 smoke detectors connected to the VT408 expansion module.
    Warning: when the analog sensors are powered off, all external sensors connected to the VT408 cease to function.
    The analog sensors connected to the VT408 are configured in the same way as the sensors connected to the monitoring module.

Setting up CAN

included page: https://vutlan.atlassian.net/wiki/spaces/DEN/pages/1016351/Setting+up+CAN

Configuring VT408

Included page: https://vutlan.atlassian.net/wiki/spaces/DEN/pages/1999038/Configuring+VT408

Copyright:

Vutlan s.r.o. (LLC)

Remote Infrastructure Monitoring and Control

43 ul.Svornosti, 821 06 Bratislava,

Slovak Republic

http://www.vutlan.com