Setting up GSM modem (v2.0.1-2.2.5)(legacy)
GSM modem is used to send notifications and to receive SMS commands.
Configuring GSM modem
Before a GSM modem can be used, you have to fill in the fields in the GSM modem properties window. Go to "GSM Modem" → "Edit" → "Edit GSM modem":
Name – the name of the GSM modem, "GSM Modem" by default;
PIN – PIN code of SIM card. This field can be empty if the PIN code is deactivated on the SIM card;
SMS Center – the number of the SMS center. At connection, the number is read from the SIM card. After editing the changes are saved on the SIM card;
Allowed numbers – the list of numbers that are allowed to send SMS commands. SMS commands from any other number will not be executed. The number must begin with a "+".
Fields describing the status of the GSM modem:
IMEI – a unique number that identifies the GSM modem;
State – the state of GSM modem;
not connected – GSM modem is not connected;
low – GSM modem is initiating or disconnecting;
normal – GSM modem is ready to send SMS;
warning – occurrence of a one-time error that does not affect the overall operation of the GSM modem;
alarm – occurrence of error that does not allow further operation of GSM modem.
Network status – network status:
registered in Operator – registered in network Operator;
registered – registered in the network;
not registered – not registered in-home network;
registration denied – registration in the home network is denied.
GSM status – general status of GSM modem:
not found – GSM modem is not found;
found, not ready – GSM modem is found but is not ready for operation;
found, ready – GSM modem is found and is ready for operation. In addition, this field shows errors that occur during the operation of the GSM modem e.g.error sending SMS.
Signal strength – the level of signal, values range from 0% to 100%.
To save the settings press "Save". To avoid repeating the procedure every time you connect the monitoring system, the settings should be saved in the flash memory of the system. Go to " System menu" → "Save settings to flash".
SMS notifications
For more information on creating SMS see the section Setting up GSM modem (v2.0.1 - v2.2.5).
To add a recipient of SMS notification go to "Add"→"Add Mailer SMS":
Name – name of notification. Can be random ( name, recipient position, etc.), "SMS" by default;
Phone number – the recipient's phone number. The number must begin with a "+".
Message – the text of the message, can be in any language. The length of the message which contains Latin characters is a max 160, and Cyrillic characters - are 70. If the length of the message exceeds this limit the SMS is split into several parts. In addition, this field allows you to edit macros (1%-7%) which insert the real values of the variables instead of the text.
To send a test message press "Send sms". The macros in the message text will be displayed in its original form (% ..). To save the notification properties, click "Save".
After filling in the properties of notification, you must specify the event, at the occurrence of which SMS notification will be sent. To do this, go to "Preferences" → "Logic schemes"→ "Add" and specify the conditions for sending SMS notifications.
For each new recipient, you have to repeat the procedure of adding SMS notification.
Before messages are sent they are queued up, which means you do not have to wait until the previous message is sent. The information on all SMS sent is displayed in the log of the monitoring system.
If an error occurs while sending a message, the log displays "SMS send error" and indicates the error number. The most common error is 515 (Ps busy), which can occur when:
not enough credit on the SIM card;
wrong SMS center number;
low signal level ( less than 15%) in the home network;
wrong SMS format ( the number must begin with a "+") or the number is invalid.
If these points do not cover your case, try to reboot the system. In addition, try to send an SMS from your mobile phone, make sure the SMS center number is the same.
SMS commands
SMS commands are used for remote control of the monitoring system. Using these commands, you can read the state and the measured values of sensors, control relays, or outlets. Phone numbers from which the SMS commands will be sent should be added to the list of allowed numbers in the modem properties ( Right click on the modem icon "Edit GSM modem" → "Allowed numbers"). In response to each SMS command, a response SMS will be sent. In case of an error, an SMS will be sent with information about the error and an example of a command. An SMS can contain only one command for only one element.
Command: reading sensor (relay, outlet) parameters
Function. get [id] or get [name], where id – is the number of the element, and name – is the name of the element. The field "get" is not case sensitive, both can be used Get, GET. The field "name" is case-sensitive.
Description. This command checks the state of the sensor or relay (outlet) and sends a response SMS to the phone, from which the command was sent.
Examples.
“get 1034” - to obtain information about the sensor with the number 1034;
”Get Analog-1” - to obtain information about the state of the element with the name of Analog-1;
“GET Relay-2” - to obtain information about the state of the element with the name of Relay-2.
See the section "Macros in the notification text" in Setting up GSM modem (v2.0.1 - v2.2.5) for further information.
Command: setting state of relay/outlet
Function. set [id] [state] or set [name] [state], where id – number of the element, name – name of the element, state – state to which relay/outlet switches. Fields "set" and "state" are not case-sensitive. The fie