VT105 / Strobe light

Documentation page: https://vutlan.atlassian.net/wiki/spaces/DEN/pages/600145921/VT105+Strobe+light

Product page: https://vutlan.com/12v-dc-devices/40-vt105-strobe.html

Function and purpose

12V LED strobe flashlight for warning and alarms. Can be used with monitoring units by connecting it to 12V relay output.

Technical specifications

VT105
Dimensions	⌀73.5mm, Height 45.5mm, cable length 3m
Weight	110g
Input	2-wire cable
Output	LED source
Voltage	12V
Rated current	120mA
Flashing frequency	90/Min
Power consumption	1 Watt
IP rating standard	IP54
Operating temperature	Temperature: Min. -50 °C - Max.105 °C
Operating humidity	Humidity : Min. 5% - Max. 95% (Non-Condensing)
Mounting	Wall or ceiling mounting
HS Code	8531 10 300
Components	Manufactured in E.U.
Special features	LED Security Alarm; Color: red; Material: plastic

Package includes

Package includes:

	Description	Quantity
1	x1 Flashing LED device with a cable, x2 back plastic panels
2	Round sticker with holes	1 pc
3	Bolts М3 8mm	2 pcs
4	2.5mm Dowels	2 pcs
5	Screws for dowels, B2.9*20	2 pcs

Connecting a strobe light using only a sticker

A strobe light can be connected to 12V 0.25A outputs of the Vutlan monitoring system. The diagram below explains how to connect "VT105 / Strobe light" to a monitoring system.

Step 1.

Remove the central part of the sticker.

Step 2.

a) Remove the protective paper from one side of the sticker. Apply the sticker to the "VT105 / Stobe light" backside.

b) Remove the protective paper from the second side of the sticker. Stick the Strobe light together with the sticker to the surface. Make sure the cable is laid out neatly using the stickers holes.

Strobe light uses a standard two-wire cable for connecting to the monitoring unit.

Step 3.

Connect the cables to 12V 0.25A outputs of the monitoring unit using a Terminal. The terminal must have a 3.81mm step.

a) Connect the black cable to a "-". Indicated by the "earth" sign.

b) Connect the red cable to a "+". Indicated by the "E1" or "E2" label.

Introduction

All Vutlan monitoring systems and switched PDUs can connect up to two alarm beacons, for example, a siren and/or strobe, and other low-current devices, for example, a dry contact output module VT11, to E1, E2 - two outputs of electronic relays.

Connection

To connect the alarm beacon to the 12V output, you need to connect the device with a cable to the terminal according to the polarity. By appropriate logic or manually in the device interface, you can turn on or off and/or give a pulse to the siren, strobe, or a signal on a dry contact output. The maximum current consumption is limited by 250 mA.

Check the voltage supply in the test mode. Go to the Main Menu -> System Structure -> Alarm in the system interface. In the window that appears, click "Pulse". The stroboscope lights up, and the siren wails. To configure alarms, you need to configure the logic.

Do not connect the loads to the outputs while the monitoring system is on.

Vutlan accessories for 12V DC outputs

12V DC relay outputs configuration

The page linked: https://vutlan.atlassian.net/wiki/spaces/DEN/pages/601030668

Connecting a strobe light using dowels

Step 1.

Remove hole parts of the sticker.

Step 2.

Screw the back panel to the backside of the strobe light using 2 M3 screws.

Step 3.

a) Drill two holes for the dowels.

b) Drill a middle hole in the surface if You plan to wire cables through the surface.

Step 4.

a) Insert the dowels into the wall.

b) Insert the adhesive sticker between the wall and the back panel.

c) Screw two M3 screws through the back panel and sticker into the dowels.

Step 5.

Once one back panel is screwed to the wall and the other is screwed to the strobe light, connect both back panels and rotate the strobe light until it is firmly connected.