VT593 / Spot leak sensor

Product page: https://vutlan.com/analog-sensors/55-vt593-spot-leak-sensor.html

Datasheet page: https://vutlan.atlassian.net/wiki/x/AQAkqQ

Keywords: #leak #leakage #spot #water #sensor #spot leak sensor #zone #floor #drip #fluid

Function and purpose

The sensor detects water by increasing capacitance on two metal poles. The detector is encapsulated in plastic housing. Due to the low applied voltages and the applied leakage detection principle, it does not rust over time.

Can be connected to any analog port (A1...A8) of the Vutlan monitoring unit.

The maximum amount of sensors and maximum length can be extended using the VT408 / Sensor extension unit.

Dimensions

Usage example

Other installation examples of similar sensors for leak detection can be found in our articles "Water leakage detection using cable sensor and spot sensor" and "Leak detection under raised floors in data centers".

Technical specifications

	VT593 / Spot leak sensor specifications
Description	The sensor has two RJ connectors. RJ 6P4C connects to the analog port of Vutlan monitoring system. RJ 4P2C connects the leak detector with two poles.
Dimensions	60×18×18 mm
Weight	60 g
Input	2 wire (WDC cable)
Detection	Capacitive
Output	RJ11 / RJ12 (6p4c)
Operating temperature	-10 °C to +80 °C
Operating humidity	5% to 95% (Non-Condensing)
Mounting	Mounting bracket included.
Power consumption	60mW
Max. distance m	100 m
HS Code	9025 80 400
Components	Manufactured in E.U.
Special features	Response time: 15 sec., Recovery time: Depends on how fast the sensor dries out

	SLD / Spot leak detector specifications
Description	The detector is used in combination with the "VT593 / Spot leak sensor" for level monitoring of conductive liquids in containers, pits, cellars, etc. The sensor has two stainless steel poles. The detector is encapsulated in plastic housing for conductive liquids. The sensor can be connected to dry contact inputs (e.g. an alarm system). Can be placed near plumbing, trays, raised floors, under equipment, sinks, aquariums, sump pumps, refrigerators, dishwashers, toilets, basements, washing machines, water heaters, and garages.
Detectable liquids	Clean, polluted & distilled water; acids; alkalis; alcohols, and other electrically conductive liquid
Dimensions	30x20x8 mm
Lengths	1-meter cable
Weight	21 g with cable
Operating humidity	20%RH～100%
Working temperature	-10℃～50℃
Outputs	Two wires, RJ 4P2C plug.
Output form	NO normally open
Special features	The measuring electrodes are resistant to chlorine and salt water (stainless steel AISI 316 / V4A)

Package content

Linked page VT593 Water spot detector package content

Package content	Description
	VT593 sensor	1 pc
	"RJ 6P4C" to "RJ 6P4C" cable 2m	1 pc
	Screw B4,2*16
	Sticker

Package content	Description
	Water spot detector	1 pc
	Screw 3.5x16
	Sticker

Installation

Installing the sensor case

Steps

Cut off the ledge at the bottom of the case.

The ledge at the bottom of the case is used for installation inside IT racks.

The sensor can be installed using a screw or a sticker

Installing the detector

Steps

The detector can be installed differently depending on the end purpose and the the surface. See below options:

A: For non-conductive surfaces.

B: For conductive surfaces.

C: For liquid level detection.

D: For installing on to vertical surfaces for level detection.

The detector can be installed onto a surface using a screw or a sticker.

The detector has a hole in the middle for a screw to fit it.

Connecting the sensor

The end poles of the sensor should not touch a conductive surface.

Connect the "VT593 / Spot leak sensor" to the monitoring unit into any available analog port. The connection is plug-an-play. Use RJ11/12 6p4c to RJ11/12 6p4c cable.
Connect the "SLD / Spot leak detector" to the "VT593 / Spot leak sensor".

Analog sensor connection

Linked page https://vutlan.atlassian.net/wiki/spaces/DEN/pages/1016274/Analog+sensors+connection

Sensor configuration

Linked page https://vutlan.atlassian.net/wiki/spaces/DEN/pages/1016314/Sensor+configuration

Cable pinouts

The sensor uses a standard Vutlan analog sensor cable (RJ11/RJ12 6P4C to RJ11/RJ12 6P4C) for connecting to the monitoring unit. You can find further instructions in the Analog Sensors Connection article
The detector uses two wires. It has a black and red wire. Plus or minus is irrelevant.

Troubleshooting

The following table describes potential problems and their possible causes. It also describes checks you can perform or possible solutions for each. After referring to this table, if you cannot resolve the problem, contact your local Vutlan sales representative for assistance.

Potential Problem	Possible Cause	Possible Solution
The sensor does not appear in the Vutlan monitoring interface	Communication lines are improperly connected.	Check the 6P4C RJ11 communication cable.
	The communication cable is inserted into the wrong port.	6P4C RJ11 communication cable must be inserted into the analog port of the Vutlan monitoring system.

Frequently asked questions

Question	Answer
Can I connect “SLD / Spot leak detector” to a 3rd party alarm system without “VT593 / Water spot sensor?	Yes, you can. But it depends on the alarm inputs charachteruistics of a 3rd party device.
Can I connect “WSD / water spot detector” to an dry contact inputs of Vutlan monitoring systems?	No, you can not. The resistance is high and this results in highly unreliable operation.

Copyright:

Vutlan s.r.o. (LLC)

Remote Infrastructure Monitoring and Control

43 ul.Svornosti, 821 06 Bratislava,

Slovak Republic

www.vutlan.com