Versions Compared

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

Connection diagram

Monitoring units VT335 has the possibility to install VT700 / GSM modem. The device is mounted and connected inside of master monitoring unit. Needed when network is absent or for reservation of a connection channel of master unit with Internet; for sending SMS notifications and SMS commands.

Supply includes

...

Image Removed

...

Image Removed

...

Image Removed

...

Image Removed

...

Image Added  End of Life: 31.03.2022

'VT760 / LTE modem' is currently produced for VT604 / Switching PDU and VT608 / Switching PDU.

Note

To install and to connect extension units: switch off the appliance, unplug from the outlet or disconnect the power connector. 

1

Image Removed
Image Added

Carefully unscrew three screws holding the cover and open it.

Note

Depending on the monitoring system, it may have 1-Wire, Antenna, GSM or Dry Contacts

module are

, or any other additional modules installed inside. Carefully open the box by unplugging, if necessary, any cables that connect from the top cover to the bottom cover.


2

Image Removed
Image Added

1) Connect the antenna cable to the modem board. Carefully connect the U-Fl antenna cable to the input U-FL connector and gently press it. If possible install the connector on the seat with a magnifying glass!

3

Image Removed

Set up the GSM modem card on 3 steel spacing sleeves on the cover, attach card to the sleeves using three M3 screws supplied with the modem.4

Image Removed

Set the SMA connector antenna cable to the rear or to the front panel of the appliance into the corresponding SMA hole. Put on the SMA connector gold-plated washer and nut from the supply, holding SMA connector with one key, securely tighten the nut with the other key. 

Note

Do not tighten SMA connector with one key, you can break the cable and the connection would be lost!

5

Image Removed

Connect 16-pin flat cable to the connectors on the modem card and on the appliance motherboard. Close and fasten the cover. If necessary, install the SIM card into the appropriate hole.6

Image Removed

Carefully place


2) Unscrew the nut and washer from the antenna cable

3

Image Added

1) Mainboard should already have two metal spacers mounted on it. If it does not, please request them from the manufacturer.

2) Place the GSM modem above the metal spacers and male pin strips located on the mainboard. Gently push the GSM board downwards so that:

   a) Male pin strip on mainboard (3pins) inserts into Female pin socket on GSM board (3pincs)

   b) Male pin strip on mainboard (7pins) inserts into Female pin socket on GSM board (7pincs)

   c) Two holes on the GSM board are located directly above metal spacers and the GSM board touches metal spacers.

3) Screw two M3 screws supplied with the modem through the holes into metal spacers as shown in the picture.

4) Insert antenna wire into hexagon mounting hole located at the front or at the back of the unit (e.g. VT335 has a front hole SMA only)

4

Image Added

The antenna wire should now stick out to the front or to the rear of the unit (e.g. VT335 has a front hole) just like shown in the picture.

1. Put a washer on the end of the antenna wire thread.

2. Screw the nut onto the antenna wire thread to the maximum with your hands.

3. Now use a wrench to tighten the nut

Note

Do not tighten the nut on the thread too hard!

4. Screw the antenna to the end of the antenna wire thread.

6

Image Added

Carefully place the top cover back so that all cover wings fit in and all

cutoffpoints

cutoff points match the panel holes.

Then use 3 screws to close the enclosure. When installing the green dry contact connectors can go tight, check the burrs and remove them with rasp!