It is possible to connect up to two readers to one Vutlan monitoring system. Please use a splitter to do this. In such a case both readers are seen by the system as one reader. This is useful when one reader is used for entrance and one reader for the exit of the same door. |
"VT107 / RFID reader" can be used for access control. It operates on a principle of contactless reading data from "VT108 / RFID cards". Each card (transponder) has a unique 40-bit identification number stored permanently (the
number is unique to each card/transponder). The reader sends this number using 1-wire bus in a format compatible with Vutlan monitoring systems.
Can be used together with all Vutlan monitoring units.
Requires "VT10 / 1-Wire extension" for VT325, VT335, VT335 DC, VT335 S, VT805, VT825, VT825 DC in order to be installed. Only one reader can be connected to one monitoring system.
"VT108 / RFID cards" are purchased separately.
# on reader | Description |
---|---|
1 | VCC ( + ) |
2 | GND ( – ) |
3 | 1-WIRE |
4 | Input Power LED red LED’a |
5 | Not used (red led) |
6 | Green LED (indicates power) |
7 | Button (it includes a bus 1-Wire to ground) |
The hole size for the screws is 4mm in diameter.
Step 1.
Install and configure "VT10 / 1-Wire extension" inside the monitoring unit and inside the web interface.
Step 2.
Connected RJ9(4P4C) cable to "VT10 / 1-Wire extension" on the monitoring system. The reader is determined automatically. Once the reader is connected, You should hear a "Beap!" sound.
Step 1. Configure Reader. Go to "System tree" >> 1-Wire wire >> iButton >> edit.
Edit name of the element. For example: RFID reader. By default iButton/Reader has a state: not connected.
If "VT108 / RFID card " is used and it is accepted. The Current state changes to "Normal" and then back to "Not connected".
If "VT108 / RFID card " is used and it is not accepted. The Current state changes to "Alarm" and then back to "Not connected".
Step 2. Inside of system's web interface go to "Access control" menu.
Step 3. Press "+" sign to add a new user and their electronic key. A modal window "Add a new key" will open.
Step 4.Press "Read" button. You will be prompted with a request:
" Please apply your electronic key to the reader. Wait for the system confirmation..."
Step 5. Place "VT108 / RFID card" of the user next to the front panel of the reader. You will hear a "Beap!" sound from Vutlan monitoring system.
Step 6. RFID card is now added to the database. Press on the newly added RFID card to edit it.
Step 7. Edit user name to Your liking.
Step 8. Add more user and their electronic keys to the database.
By default iButton/Reader has a state: not connected.
If "VT108 / RFID card " is used and it is accepted. The Current state changes to "Normal" and then back to "Not connected".
If "VT108 / RFID card " is used and it is not accepted. The Current state changes to "Alarm" and then back to "Not connected".
Then we can setup a simple logic. For example, we want to activate an electromagnetic lock if correct RFID card is used. And open lock using Exit button using dry contact input. Picture below shows such a logic example.
VT107 / RFID reader | |
---|---|
Supply voltage | 7...25V |
Supply current | 30...55 mA |
Operating frequency built-in antenna | 125 kHz |
The speed of reading data from the transponder | RF/64 (1953b/s) |
Supply voltage LED red | 0…14V |
HS Code | 8471 90 000 |
Max. range readings | 15 cm (MAX.) |
Antenna | Built-in device |
Interfaces | 1-Wire |
Dimensions | 82 x 82 x 22 mm |
The distance between the retaining pins | 42 mm |
Voltage failure reader | +/- 30 V |
Please see section: VT107 package content
Developer notes: